Microcontroller based Water Level Controller cum Motor Protector

3,8025,703

Project kit PriceQuantity
Professional 3,802
Assembled 4,515
Combo 5,109
Learning 5,703
SKU: IQ-47 Category:

Description

Abstract:

The Microcontroller based Water Level Controller cum Motor Protector controls ‘on’ and ‘off’ conditions of the motor depending upon the level of water in the over head tank (OHT), the status of which is displayed on an LCD module. The circuit also protects the motor from high voltages, low voltages, fluctuations of mains power and dry running.

The circuit of the Microcontroller based Water Level Controller cum Motor Protector comprises of the operational amplifier LM324, microcontroller AT89C51, optocoupler PC817, regulator 7805 and an LCD module. Port pins P2.0 through P2.2 of the AT89C51 (IC2) are used to sense the water level, while pins P2.3 and P2.4 are used to sense the under-voltage and over-voltage, respectively. Pin P3.4 is used to control relay RL1 with the help of optocoupler IC3 and transistor T5 in the case of under-voltage, over-voltage and different water-level conditions. The LM324 (IC1) is a quad operational amplifier (op-amp). Two of its op-amps are used as comparators to detect under- and over-voltage. In normal condition, output pin 7 of IC1 is low, making pin P2.3 of IC2 high. When the voltage at pin 6 of N1 goes below the set reference voltage at pin 5 (say, 170 volts), output pin 7 of N1 goes high. This high output makes pin P2.3 of IC2 low, which is sensed by the microcontroller and the LCD module shows ‘low voltage.’
In normal condition, pin 1 of N2 is high. When the voltage at pin 2 of N2 goes above the set voltage at pin 3, output pin 1 of N2 goes low. This low signal is sensed by the microcontroller and the LCD module shows ‘high voltage.’
Presets VR1 and VR2 are used for calibrating the circuit for under- and over-voltage, respectively. When water in the tank rises to come in contact with the sensor, the base of transistor BC548 goes high. This high signal drives transistor BC548 into saturation and its collector goes low. The low signal is sensed by port pins of microcontroller IC2 to detect empty tank, dry sump and full tank, respectively.

When water in the tank is below sensor A, the motor will switch on to fill water in the tank. The LCD module will show ‘motor on.’ The controller is programmed for a 10-minute time interval to check the dry-run condition of the motor. If water reaches sensor B within 10 minutes, the microcontroller comes out of the dry-run condition and allows the motor to keep pushing water in the tank. The motor will remain ‘on’ until water reaches sensor C. Then it will stop automatically and the microcontroller will go into the standby mode. The LCD module will show ‘tank full’ followed by ‘standby mode’ after a few seconds. The ‘standby mode’ message is displayed until water in the tank goes below sensor A. In case water does not reach sensor B within 10 minutes, the microcontroller will go into the dry-running mode and stop the motor for 5 minutes, allowing it to cool down. The LCD module will show ‘dry-sump1.’ After five minutes, the microcontroller will again switch on the motor for 10 minutes and check the status at sensor B. If water is still below sensor B, it will go into the dry-running mode and the LCD module will show ‘dry-sump2.’ The same procedure will repeat, and if the dry-run condition still persists, the display will show ‘dry-sump3’ and the microcontroller will not start the motor automatically. Now you have to check the line for water and manually reset the microcontroller to start operation. In the whole procedure, the microcontroller checks for high and low voltages. For example, when the voltage is high, it will scan for about two seconds to check whether it is a fluctuation. If the voltage remains high after two seconds, the microcontroller will halt running of the motor. Now it will wait for the voltage to settle down. After the voltage becomes normal, it will still check for 90 seconds whether the voltage is normal or not. After normal condition, it will go in the standby mode and start the aforementioned procedure.

Additional information

Weight N/A
Project kit

Professional, Assembled, Combo, Learning

18 reviews for Microcontroller based Water Level Controller cum Motor Protector

  1. medical Technologist

    What a great resource!

  2. Medical Billing

    Superb blog post, I have book marked this internet site so ideally I’ll see much more on this subject in the foreseeable future!

  3. Swiss Ball Exercises

    Thanks for an idea, you sparked at thought from a angle I hadn’t given thoguht to yet. Now lets see if I can do something with it.

  4. aerospace engineers

    I’ve recently started a blog, the information you provide on this site has helped me tremendously. Thank you for all of your time & work.

  5. shah

    required hex code for water level control

    • admin

      If you are a localite please visit our shop for your requirement or send us the specifications og micro-controller you wish to burn data in

  6. Phlebotomy Certification

    Thank you, I have recently been searching for information about this topic for ages and yours is the best I have discovered so far.

  7. James D Despain

    Thanks for the great post. Page Bookmarked

  8. admin

    Please send me the address of the webpage, it should not have happened. We are extremely sorry for the discomfort.

    • zano

      hie thank u for the circuit diagram im working on this same project bt im using the pic.

  9. colon cleansing

    If you could e-mail me with a few suggestions on just how you made your blog look this excellent, I would be grateful.

    • admin

      Ashudeep Kain
      ashudeepkain@gmail.com

      Contact this guy for blog design and development. He is the creator and developer of whole site.

  10. frank

    very wonderful work!

    • frank

      Please could you send me a guide to developing the assembly language program for the project.my e-mail is frank_assisi2003@yahoo.com. thanks

  11. simba

    hie im doing a project on water level control using a pic16f877, can you please help me with a circuit diagram

  12. simba

    hie im a final year student doing a project on water level control using a pic16f877. can you please help me with a circuit diagram

  13. thumbnails explorer

    Hello there, You have done an incredible job. I will certainly digg it and personally suggest to my friends.

  14. google

    I liked your article is an interesting technology
    thanks to google I found you

  15. jogi

    pin configuration in program is wrong. even there is a logical error.
    if u can help, please help me out

  16. Aditya

    Require program for MicrocontrollerbasedWaterLevelControllercumMotorProtector plzz help me…

  17. mohit rajput

    Require program for MicrocontrollerbasedWaterLevelControllercumMotorProtector plzz help me…and ckt diagram

Add a review

Your email address will not be published. Required fields are marked *

Connect with Facebook


Provided by orange county fountain repair